Training project
MECHATRONIC RACE CAR – DIFFERENTIAL GEARBOX, ELECTRONICS AND WI-FI CONTROL
From milled part to the web page on your phone: gearbox with spur and bevel gears, servo steering, performance PCB and Arduino Nano 33 IoT in 22 consecutive tasks
Request a quoteOpen 3D model in Autodesk Fusion
- Original Fusion model
- Learning tasks in the MLS learning system
- Parts
- 26
- Length
- 293.11mm
- Width
- 128.6mm
- Mass
- 3.4kg
What it is about
The mechatronic variant of the race car combines machining, 3D printing, electronics and programming in one vehicle. An aluminium 6061 chassis carries gearbox assembly 000070 and electrical assembly 000071. The gearbox (19 items, about 340 g) is a differential with a spur gear m0.5 z30, four bevel gears m0.5 z20, one bronze differential pin, the gear pair z=22/44, a bevel gear pair whose large gear is also the differential cage (m=0.6 per title block; the 3D model with ≈ 0.87 is faulty and will be corrected; PLA according to the print note), left and right drive shafts and five deep-groove ball bearings. The electrical assembly (11 items) sits on the printed electronics carrier: performance PCB with “IC 293 B” motor driver, 5 V module and slide switch, Arduino Nano 33 IoT, DC motor with drive gear, 9 g servo with printed servo horn (steering) and three 9 V batteries. The car is controlled via a web server on the Arduino, opened over Wi-Fi from a phone or laptop. Printed TPU tyres on new rims replace the O-rings, and the drive shafts replace the rear axle of the mechanical variant. Eight part types, wheel carrier, left and right steering knuckles, four suspension axles, track rod, windscreen, front and rear spoiler, are adopted unchanged from the project “Rennwagen mechanisch”. Full assembly: 21 items, 59 pieces at top level, length 293.11 mm, width 128.6 mm, wheelbase 200 mm, scale 1:2. The title-block mass of about 3.4 kg is unrealistically high because the purchased electrical parts are calculated with placeholder materials in the 3D model. In this content the drawing always prevails.
General tolerance: DIN ISO 2768m-K (so im Schriftfeld) · Scale: 1:2
Learning objectives
- Produce and inspect turned, milled and printed parts to drawing, including fits, bearing seats and material notes.
- Explain the design and function of a differential gearbox with spur and bevel gears and assemble and test the gearbox assembly.
- Populate and solder a PCB, wire an electrical assembly and commission it systematically.
- Program an Arduino Nano 33 IoT and control the car via a Wi-Fi web server.
- Plan and carry out final assembly across three levels (mechanics, electrics, software) and document it with acceptance and a driving test.
- Recognise contradictions between task, drawing, parts list and 3D model, resolve them with reasons and document them.
AI mentor
This project is available in the AI mentor as 31 missions, from getting started through the parts to the review. With a licence the AI mentor tailors the tasks to you.
Parts
- 01
Chassis
The chassis is the backbone of the mechatronic race car: a CNC-milled part in aluminium 6061 with the main dimensions **258 × 80 × 52 mm** (drawing 000019, two sheets).
- 02
Front axle
The front axle is a turned part in stainless steel 1.4305 weighing about 8 g, needed twice (drawing 000011). Over an overall length of 28.1 mm it carries a **Ø12 collar** with a **bolt circle 3 × 120° on Ø9±0.
- 03
Rim
The rim is a turned-and-milled part in aluminium 6061 weighing about 56 g, needed four times (drawing 000012). Outside Ø45 at a width of 35 mm, with the **tyre seat Ø41±0.
- 04
Tyre
The tyre is the only elastic part of the race car: an FDM print in **TPU, black**, needed four times (drawing 000024). It is **Ø50 outside, 32 mm wide** and sits with **Ø41 inside** on the Ø41±0.
- 05
Axle housing (gearbox housing)
The axle housing is the milled housing of gearbox assembly 000070 (item 1, 1 off) made of aluminium 6061 weighing about 75 g. Its outside dimensions are **70 × 58 × 27 mm**.
- 06
Cover plate 24 × 24 × 2
The cover plate is a small 24 × 24 × 2 mm plate of aluminium 6061 (drawing 000017, about 1.3 g each), needed **twice** in the gearbox assembly (item 11).
- 07
Bearing cap Ø25 (differential cover)
The bearing cap is an annular cover with **Ø25 mm outside diameter and only 6.4 mm thickness** (drawing 000006, title “Abdeckung Differential”, item 5 of the gearbox assembly, 1 piece).
- 08
Housing cover 63 × 58 (differential cover)
The housing cover is the largest printed part of the gearbox assembly: **63 × 58 mm footprint and 13 mm height** (3D), item 8 of the gearbox assembly, 1 off. It covers the gearbox and protects gears and differential against dirt.
- 09
Drive shaft
The drive shaft is the smallest turned part of the gearbox: **32±0.1 mm long, three stepped diameters, all f7** — ⌀6f7, ⌀5f7 and ⌀4f7. Steel, finished mass about 5.7 g, drawing 000004 at a scale of 5:1.
- 10
Left drive shaft
The left drive shaft carries torque from the side bevel gear of the differential to the left rear wheel. It is 38.
- 11
Right drive shaft
At **57 mm** the right drive shaft is the longest shaft of the gearbox and carries torque from the side bevel gear of the differential to the right rear wheel.
- 12
Differential pin Ø4 × 24
The differential pin is a small turned part made of bronze, **Ø4 × 24 mm, about 2.1 g** (drawing 000010, scale 2:1).
- 13
Drive spur gear
The drive spur gear (m = 0.5, z = 30, steel, about 7 g) is not cut by you: the starting point is **semi-finished part 21103000**, a ready-cut spur gear.
- 14
Bevel gear
The bevel gears (m = 0.5, z = 20, steel, about 1.5 g each) are the heart of the differential.
- 15
Gear pair
The gear pair is a **bevel gear pair**: the axes of the two gears are perpendicular and intersect (confirmed on the 3D model). **000008_2** is the bevel pinion (z = 22, tip circle in the still faulty model ≈ 20.
- 16
Electronics carrier
Electronics carrier 000025 is the printed support for the entire electrical system: the performance board with the Arduino Nano 33 IoT, three 9 V batteries, the servo with the steering link and the DC motor sit on it; it is itself screwed t …
- 17
Steering (servo lever)
The steering is a small servo lever in **black PLA** printed by FDM (drawing 000020, 1 piece, about 0.6 g).
- 18
Performance board (motor driver and supply board)
Performance board 000031 is the race car's power electronics: 49.5 × 35.5 mm, populated with the motor driver IC "IC 293 B" in a DIL16 package, a 5 V module from the Würth MagI³C-FDSM series, an on-on slide switch (Würth 450301014042), **tw …
- 19
Control and software (Arduino sketch with WiFi web server)
With this task the race car drives: the sketch **Rennwagen_Webserver.ino** is loaded onto the Arduino Nano 33 IoT of the electrical assembly with the Arduino IDE.
- 20
Wheel carrier
The wheel carrier is a brass flat bar of about 14 g which links the two steering knuckles to the front of the chassis. Two ⌀5H8 (E) bores with Ra 0.8 at a spacing of 52±0.
- 21
Wheel carrier left and right (steering knuckles)
The left and right wheel carriers are **items 12 and 13** of the mechatronic race car's parts list (numbers 000015 and 000016; items 3 and 4 in the mechanical project): two mirror-image steering knuckles of stainless steel AISI 304, each ab …
- 22
Suspension axle (pivot pin)
The suspension axle is a shouldered pin of stainless steel AISI 304 weighing about 4 g, needed four times — it forms all four joints of the front axle. Over an overall length of 23.
- 23
Track rod
At about 10 g the track rod is the lightest in-house part of the mechanical race car (the mechatronic one has lighter ones, such as the printed steering part at about 0.6 g): a brass flat bar 4 −0.
- 24
Windscreen
At about 200 g the windscreen is the **second heaviest single part** of the race car – 10.0 % of the total mass in the mechanical project, 5.9 % of the (unrealistically high) title-block mass of about 3.
- 25
Front spoiler
The front spoiler is an FDM printed part in PLA: 125.6 × 60 × 22.11 mm in size, weighing about 28 g, adopted unchanged from the mechanical project (item 8 of the mechatronic race car's parts list).
- 26
Rear spoiler
The rear spoiler is the second FDM printed part in the mechanical project and one of several in the mechatronic one (parts list item 9): 119.66 mm wide, 34.
Assemblies
- 01
Gearbox assembly (differential gearbox)
Gearbox assembly 000070 combines the in-house manufactured parts with five deep-groove ball bearings and seven standard-part items into a **differential gearbox**: 19 items, 40 individual parts, about 340 g.
- 02
Electrical assembly (assembly, wiring, commissioning)
Electrical assembly 000071 turns individual parts into an electrical system: 11 items, 21 pieces — carrier, performance board, Arduino Nano 33 IoT, 9 g servo with steering link, DC motor with m0.
- 03
Mechatronic race car full assembly (final assembly)
The full assembly is the ready-to-drive race car: chassis with gearbox assembly 000070 and electrical assembly 000071, front axle of wheel carrier, steering knuckles, suspension axles and track rod, four wheels of rim and printed TPU tyre, …
Content version 1.0.0.
Whether a workshop, a class set or a completely new training project: we will find the right model.