Knowledge
TECHNICAL TERMS.EXPLAINED BRIEFLY.
37 terms from manufacturing, drawings, inspection, materials, electrical and mechatronics, CAD and training methods. Each with a definition, explanation, worked example, common mistakes and an example from our training projects.
Manufacturing
Machining, bending, joining: workshop terms with worked calculations.
Cutting speed
Cutting speed vc is the speed at which the cutting edge moves relative to the workpiece, given in m/min.
Feed
Feed is the distance the tool or workpiece travels in the feed direction per revolution (f in mm) or per cutting edge (fz in mm).
Rake angle and clearance angle
Clearance angle α, wedge angle β and rake angle γ describe the shape of the cutting edge and add up to 90°.
Climb and conventional milling
In climb milling the cutter edge moves in the feed direction while engaged, and the chip goes from thick to thin.
Tap drill hole
The tap drill hole is the hole into which an internal thread is cut or formed.
ISO metric thread
The ISO metric thread is the standardised fastening thread with a 60° flank angle, designated by M and the nominal diameter in millimetres, e.g.
Chamfer
A chamfer is a bevelled workpiece edge.
Undercut
An undercut is a small groove at the transition between two diameters of a shaft or at the end of a thread.
Countersink and counterbore
A countersink or counterbore is an enlargement at the start of a hole that takes the screw head.
Flat pattern
The flat pattern is the flat blank of a bent part, i.e. the shape the sheet has before bending.
Bend radius and springback
The bend radius is the inner radius of a bend; below a material-dependent minimum bend radius the outer fibre cracks.
Drawings and tolerances
Reading technical drawings and understanding what dimensions and tolerances specify.
Reading a technical drawing
A technical drawing describes a part completely and unambiguously: shape in views, size by dimensions, accuracy by tolerances, plus material and surface.
Sectional view
A sectional view shows a part as if it had been cut along an imaginary plane.
Dimensioning
Dimensioning is the entry of dimensions on a technical drawing, consisting of dimension line, extension lines, terminations and the dimension value.
Parts list
The parts list (bill of materials) is the list of all parts of an assembly with item number, quantity, name, part number or standard designation and material.
General tolerances
General tolerances apply to all dimensions on a drawing that have no individual tolerance.
Fit
A fit describes how two parts with the same nominal size go together, typically a hole and a shaft.
Inspection and measurement
Reading measuring instruments, planning characteristics, assessing surfaces.
Roughness Ra and Rz
Ra and Rz are parameters for surface roughness.
Reading a caliper (vernier)
The vernier is an auxiliary scale on the slide of a caliper that allows fractions of a millimetre to be read.
Micrometer
The micrometer is an instrument for outside dimensions in which a measuring spindle with a fine thread converts length into rotation.
Inspection equipment
Inspection equipment covers all devices used to determine whether a workpiece meets the required characteristics.
Inspection plan and characteristic
An inspection characteristic is a property of a workpiece that is checked, such as a diameter, an angle or a roughness.
Materials
Designating steel and aluminium, understanding heat treatment.
Steel designation
In Europe steels are designated by a steel name or a material number.
Aluminium 5754 and 6060
EN AW-5754 (AlMg3) and EN AW-6060 (AlMgSi) are two common wrought aluminium alloys. 5754 is non-heat-treatable, easy to form and very corrosion resistant, typical for sheet; 6060 is heat-treatable, extrudes very well and anodises well, typical for profiles.
Hardening and tempering
Hardening is a heat treatment in which steel is heated and cooled so quickly that a very hard but brittle microstructure (martensite) forms.
Electrical and mechatronics
Microcontrollers, motor control and soldering on a real vehicle.
Microcontroller and Arduino
A microcontroller is a computer on a single chip with processor, program memory, working memory and inputs and outputs.
PWM (pulse-width modulation)
Pulse-width modulation is a method in which a voltage is switched on and off rapidly to control a load continuously.
H-bridge and motor driver
An H-bridge is a circuit of four electronic switches with a DC motor between them like the crossbar of the letter H.
Mecanum wheel
A Mecanum wheel is a wheel with freely rotating rollers around its circumference whose axes are usually at 45° to the wheel axis.
Soft soldering in electronics
Soft soldering joins components and circuit board with a molten solder whose melting temperature is below 450 °C, without melting the parts themselves.
CAD and digital manufacturing
Designing with parameters, planning assemblies, from model to NC program and printed part.
Parametric design
Parametric design means building a 3D model from dimensions, constraints and a sequence of modelling steps that can be changed later.
Top-down and bottom-up design
In bottom-up design individual parts are designed on their own first and then assembled.
CAM
CAM (computer-aided manufacturing) is computer-aided planning of manufacturing: toolpaths are calculated from the 3D model, simulated and output as an NC program for a specific machine via a post processor.
FDM 3D printing
FDM (fused deposition modelling) is a 3D printing process in which a plastic filament is melted and deposited layer by layer through a nozzle.
Training methods
How companies and vocational schools organise learning.
Four-step method
The four-step method is an instruction method for in-company training with the steps prepare, demonstrate and explain, have the trainee repeat and explain, and practise.
Complete action
The complete action is a model for independent learning in six steps: inform, plan, decide, carry out, check and evaluate.
Learning field
A learning field is a thematic unit in the framework curriculum of the Standing Conference of Ministers of Education (KMK) for vocational school teaching.
From term to component
All examples come from Stern Didactic’s training projects. In Nullpunkt apprentices manufacture the parts virtually from the original drawings.