Training project
BUGGY – SHEET METAL AND MACHINING PROJECT
Bending, unfolding, milling and turning: from sheet blank to a rolling buggy
Request a quoteOpen 3D model in Autodesk Fusion
- Original Fusion model
- Learning tasks in the MLS learning system

- Parts
- 7
- Length
- 145mm
- Width
- 112mm
- Height
- 75mm
- Mass
- 1.3kg
-
Training project · Buggy
BUGGY.SHEET METAL AND MACHINING PROJECT.
Bending, unfolding, milling and turning: from sheet blank to a rolling buggy. What you see is our own design model from Fusion: 29 bodies, about 15 centimetres long. Scroll: the model opens up part by part.

-
01 / 09
7 PARTS.EACH ONE MADE.
Training project focused on sheet metal: U-bent rear body with a dimensioned flat pattern (170.52 mm), sheet angles, a wire bending part, combined with a milled steel chassis, aluminium engine block and turned wheels on ISO 7379 shoulder screws.

-
02 / 09
CHASSIS.MILLED.
At about 690 g the chassis is the heaviest part of the buggy, more than half of the total mass of about 1.3 kg sits in this steel plate alone.
What this part involves
- Check the blank and mill the datum face
- Mill the opposite face parallel to 10 mm
- Mill the four sides to 130 × 70 mm
- Mark out or program the top-view hole pattern

-
03 / 09
ENGINE BLOCK.MILLED.
The engine block is the most demanding milled part of the buggy: an aluminium block 70 × 50 × 25 mm with a prismatic trapezoidal pocket, angled faces, M4 threads and Ø3 +0.1/0 holes.
What this part involves
- Clamp the blank and mill the datum face
- Mill the opposite face to 25 mm and the four sides to 70 × 50 mm
- Set the zero and create the setup in Autodesk Fusion
- Program facing, two operations

-
04 / 09
WHEEL.TURNED.
The wheel is the buggy's only turned part and the only part in the whole project with a genuine ISO fit.
What this part involves
- Clamp the bar and face it
- Centre and pre-drill Ø5.8 mm
- Rough and finish the Ø34 outside diameter
- Turn the Ø21 collar and Ø11 hub with the 11 and 5 steps

-
05 / 09
REAR BODY.BENT.
The rear body is the didactic heart of the buggy project: a U-shaped folded steel sheet 1 mm thick whose flat pattern is explicitly dimensioned on the drawing as 170.52 × 35 mm.
What this part involves
- Measure the sheet thickness and calculate the flat pattern
- Trial bend on an offcut
- Mark out the flat pattern
- Cut the strip to length and width

-
06 / 09
SEAT.BENT.
The seat is a simple sheet metal angle 25 × 25 × 25 mm from 2 mm steel sheet with one 90° bend, and of all things the project's smallest sheet part contains the elegant calculation.
What this part involves
- Measure the sheet thickness and calculate the flat pattern
- Trial bend on an offcut
- Mark out the strip, both seats together
- Drill the Ø8.6 mm holes

-
07 / 09
BENCH SEAT.BENT.
The bench is the same sheet metal angle as the seat, cross-section 25 × 25 mm from 2 mm steel sheet, one 90° bend, an identical developed length of 46.52 mm.
What this part involves
- Measure the sheet thickness and calculate the flat pattern for the family
- Trial bend for the whole family
- Cut the strip and cut the widths
- Mark out the hole centres from the part centre

-
08 / 09
WINDSCREEN.BENT.
At about 6.5 g the windscreen is the buggy's lightest part and the project's only wire bent part: a U-shaped bracket from Ø3 mm round wire, 60 mm wide and 25 mm high, whose two feet are bent over 5 mm of length at 165° and serve as insertion tabs.
What this part involves
- Measure the wire diameter and calculate the flat pattern
- Mass calculation as a cross-check
- Cut the wire with allowance and deburr the ends
- Trial bend on an offcut

-
09 / 09
ASSEMBLED.INSPECTED.
Produce and inspect parts to drawing. Apply tolerances, fits and surface specifications.
What this part involves
- Incoming inspection of all 29 parts
- Recalculate the mass balance
- Pre-measurement on the chassis and the wheels
- Lay the chassis down as the base and fit the mounted parts hand tight

Model: Autodesk Fusion, Stern Didactic. Taken over without simplification; what is hidden in Fusion is missing here too.
What it is about
Training project focused on sheet metal: U-bent rear body with a dimensioned flat pattern (170.52 mm), sheet angles, a wire bending part, combined with a milled steel chassis, aluminium engine block and turned wheels on ISO 7379 shoulder screws. Includes the five-part 2021 CAD/CAM video series with full transcripts. 145×112×75 mm, about 1.3 kg.
General tolerance: DIN ISO 2768-m-K · Scale: 1:2
Learning objectives
- Produce and inspect parts to drawing.
- Apply tolerances, fits and surface specifications.
- Assemble the unit and record a function test.
Nullpunkt · The workshop in your browser
Apprentices also build this project virtually: 7 parts, on real machines, with the original drawings from Autodesk Fusion.
AI mentor
This project is available in the AI mentor as 10 missions, from getting started through the parts to the review. With a licence the AI mentor tailors the tasks to you.
The material is available as a ready kit in our shop.
Whether a workshop, a class set or a completely new training project: we will find the right model.