Skip to content
Stern Didactic GmbH

Training project

WIND TURBINE – MACHINING PROJECT

Turning, milling, fits and assembly: from steel and aluminium stock to a working wind turbine

Request a quoteOpen 3D model in Autodesk Fusion

  • Original Fusion model
  • Learning tasks in the MLS learning system
Wind turbine: our design model, overall view.
Parts
7
Height
413mm
Mass
3.2kg
  1. 01 / 09

    7 PARTS.EACH ONE MADE.

    Classic metal-trades training project: seven parts in steel and aluminium are turned, milled, drilled, reamed and threaded, with real ISO fits (Ø20H8/e8 sliding fit, Ø8H7 for the ISO 7379 shoulder screw), roughness down to Ra 0.8 and a DIN 76-A thread undercut.

    Wind turbine in exploded view.
  2. 03 / 09

    TURBINE TOWER.TURNED.

    The tower is the longest part of the project and its machining centrepiece: an aluminium truncated cone, 220 mm long, Ø50 mm at the bottom and Ø30 mm at the top.

    Turned part · Aluminium · Guide time 3 h

    What this part involves

    1. Calculate the taper data and define the method
    2. Clamp the blank and face the first end
    3. Drill the Ø5 mm tapping hole to a depth of 20 mm
    4. Cut the M6 thread to a depth of 15 mm
    Wind turbine: Turbine tower.
  3. 05 / 09

    HUB.TURNED.

    The hub is the rotor hub of the wind turbine and carries the didactically most important fit of the project: its central Ø20H8 bore with Ra 0.8 runs on the Ø20e8 shank of the shaft and thereby forms a pure clearance fit.

    Turned part · Aluminium · Guide time 3.5 h

    What this part involves

    1. Calculate the fit before the first chip
    2. Clamp the blank, face and pre-drill
    3. Bore to Ø19.8 mm and finish the outside diameter
    4. Re-clamp and produce the width
    Wind turbine: Hub.
  4. 07 / 09

    WING SEAT.MILLED.

    At about 13 g the wing seat is the smallest and lightest part of the turbine and is needed three times: it connects one wing each to the hub.

    Milled part · Aluminium · Guide time 1.5 h

    What this part involves

    1. Clamp the blank strip and mill the datum face
    2. Mill the 20 mm width and check squareness
    3. Mark out or program the hole positions from the reference edge
    4. Centre and drill the four Ø4.5 mm holes
    Wind turbine: Wing seat.
  5. 09 / 09

    ASSEMBLED.INSPECTED.

    Produce turned and milled parts to drawing, applying general and ISO tolerances confidently. Produce and measure fits (H8/e8, H7) and judge their function.

    Assembly · Guide time 1 h

    What this part involves

    1. Pre-assembling the rotor
    2. Screwing the axle into the head
    3. Fitting the rotor
    4. Tower onto the base

    Request a quoteProject details

    Wind turbine, fully assembled.

Model: Autodesk Fusion, Stern Didactic. Taken over without simplification; what is hidden in Fusion is missing here too.

What it is about

Classic metal-trades training project: seven parts in steel and aluminium are turned, milled, drilled, reamed and threaded, with real ISO fits (Ø20H8/e8 sliding fit, Ø8H7 for the ISO 7379 shoulder screw), roughness down to Ra 0.8 and a DIN 76-A thread undercut. Assembly with standard parts and the function test of the free-running rotor complete the project. Height 413 mm, total mass 3243 g.

General tolerance: DIN ISO 2768-m-K · Scale: 1:5

Learning objectives

  • Produce turned and milled parts to drawing, applying general and ISO tolerances confidently.
  • Produce and measure fits (H8/e8, H7) and judge their function.
  • Cut threads, select standard parts and designate them correctly.
  • Achieve and verify surface requirements (Ra 0.8–12.5) with suitable processes.
  • Assemble a unit correctly and record a function test.

AI mentor

This project is available in the AI mentor as 10 missions, from getting started through the parts to the review. With a licence the AI mentor tailors the tasks to you.

Open missionsHow it works

The material is available as a ready kit in our shop.

Whether a workshop, a class set or a completely new training project: we will find the right model.

Contact